Planet BSP-115HP-5A Hybridní PoE solární switch, 5x 1Gb, 1x SFP, 1x PoE++ 802.3bt, 2x 802.3at, 2x at/pasivní, -20~65°C

Solar-powered PoE switch with an integrated MPPT controller offers 5× RJ-45 10/100/1000 Base-T with PoE IEEE 802.3af/at/bt, 65 W PoE budget, DIP switch, and 1× SFP 100/1000 Base-X.
1/2 pins for PV (photovoltaic) panels + some types of generators (water or wind), pins 3/4 for DC power, pins 5/6 for battery charging/discharging. There is a DIP switch on the front for configuring PoE and VLAN. The DIP switch on the back is used for setting battery type and voltage.
ESD protection up to 4 kV (contact), 8 kV (air), temperature sensor (detection -20 to 100 °C), IP30 protection (metal enclosure), fanless, wall or desktop mounting, operating temperature -20 to +65 °C.

A solar PoE switch that supports simultaneous use of solar (PV), DC, and battery power. Energy obtained from the solar panel is stored in a 12 or 24 V battery. When solar power is not available, the battery is used to power the switch and connected devices.

This solution provides the ability to power connected active devices, such as IP cameras, switches, converters, or Wi-Fi units, continuously and without dependence on the power grid. Thus, the application is suitable for ensuring surveillance in park environments, forests, cabins, or large agricultural and industrial areas. Thanks to uninterrupted power supply, it can also be used for building telecommunication points for local internet providers.

Battery management:

• Supports lithium (Lithium, Li-Fe) and lead-acid batteries (Lead-acid, Pb), option to choose
• Input power (PV IN): min. voltage 15–27 V DC (12V battery), 32.45 V DC (24V battery), max. current 5 A, power up to 135 W (for 12V battery, 225 W for 24V battery), support for DC power 15-24 V (with 12V battery) or 32-36 V (with 24V battery)
• Current battery usage status
• MPPT (Maximum Power Point Tracking) charge controller
• Reverse current protection (prevents reverse flow of electricity into the photovoltaic panel)
• Overcurrent protection and reverse polarity protection (for battery and charging electrodes)

TECHNICAL SPECIFICATIONS

Physical properties:

Ports: 1× RJ-45 10/100/1000 Base-T with PoE++, 2× RJ-45 10/100/1000 Base-T with PoE+, 2× RJ-45 10/100/1000 Base-T with PoE, 1× SFP Base-X
Memory: 2K MAC addresses, 2.5 Mb buffer
Throughput: 12 Gbps bus, operational 8.92 Mpps (64B)
Form factor: desktop, wall-mount
Power Supply (switch): via photovoltaic panels (DC 15–45 V), from battery (DC 12/24 V), or using DC power (pin 3/4) 15-24 V (with 12V battery) or 32-36 V (with 24V battery), total power consumption up to 75.6 W (full load with PoE power)
Power requirements:
Solar panel: 15–27 V DC (12V battery), 32-45 V DC (24V battery)
Battery: 12/24 V, lithium (Lithium, Li-Fe) and lead-acid batteries (Lead-acid, Pb)
DC power: 15-24 V (with 12V battery) or 32-36 V (with 24V battery)
Output power: 1× PoE++ RJ-45, 2× PoE+ RJ-45, 2× PoE RJ-45, 6-pin terminal block (2× PV panel inputs, 1× power input/output for 12/24V battery, 2× DC power inputs)
Protection: ESD up to 4 kV contact, 8 kV air (ethernet)
Operating temperature: -20 to +65 °C
Dimensions: 159 × 142 × 34 mm
Weight: 690 g

PoE Functions:

Total power output: up to 65 W, 802.3af/at/bt
Number of injectors: 1× up to 60 W, 2× up to 35 W, 2× up to 25 W (at DC 24 V) or up to 35 W (at DC 48 V)
Power type: End-span
Advanced features:

The switch features a manual mode switch:

• Alive check - monitors the status of connected devices in real-time; if a device stops responding, it is reset by power cycling.
  
• VLAN - ports are logically separated from each other; this mode can prevent unwanted multicast and broadcast storms.
  
• Extend - switch powers devices up to 250 m with reduced throughput of 10 Mb/s per port.
  

Other downloads